PIC16F785-I/SO【PDF 32/206 页】IC PIC MCU FLASH 2KX14 20SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3880

28页 29页 30页 31页 [32页]33页 34页 35页 36页

127

8272E–AVR–04/2013

ATmega164A/PA/324A/PA/644A/PA/1284/P

value when the counter is running with none or a low prescaler value, there is a risk that the new

ICRn value written is lower than the current value of TCNTn. The result will then be that the

counter will miss the compare match at the TOP value. The counter will then have to count to the

MAX value (0xFFFF) and wrap around starting at 0x0000 before the compare match can occur.

The OCRnA Register however, is double buffered. This feature allows the OCRnA I/O location

to be written anytime. When the OCRnA I/O location is written the value written will be put into

the OCRnA Buffer Register. The OCRnA Compare Register will then be updated with the value

in the Buffer Register at the next timer clock cycle the TCNTn matches TOP. The update is done

at the same timer clock cycle as the TCNTn is cleared and the TOVn Flag is set.

Using the ICRn Register for defining TOP works well when using fixed TOP values. By using

ICRn, the OCRnA Register is free to be used for generating a PWM output on OCnA. However,

if the base PWM frequency is actively changed (by changing the TOP value), using the OCRnA

as TOP is clearly a better choice due to its double buffer feature.

In fast PWM mode, the compare units allow generation of PWM waveforms on the OCnx pins.

Setting the COMnx1:0 bits to two will produce a non-inverted PWM and an inverted PWM output

can be generated by setting the COMnx1:0 to three (see Table on page 134). The actual OCnx

value will only be visible on the port pin if the data direction for the port pin is set as output

(DDR_OCnx). The PWM waveform is generated by setting (or clearing) the OCnx Register at

the compare match between OCRnx and TCNTn, and clearing (or setting) the OCnx Register at

the timer clock cycle the counter is cleared (changes from TOP to BOTTOM).

The PWM frequency for the output can be calculated by the following equation:

The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).

The extreme values for the OCRnx Register represents special cases when generating a PWM

waveform output in the fast PWM mode. If the OCRnx is set equal to BOTTOM (0x0000) the out-

put will be a narrow spike for each TOP+1 timer clock cycle. Setting the OCRnx equal to TOP

will result in a constant high or low output (depending on the polarity of the output set by the

COMnx1:0 bits.)

A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set-

ting OCnA to toggle its logical level on each compare match (COMnA1:0 = 1). This applies only

if OCR1A is used to define the TOP value (WGM13:0 = 15). The waveform generated will have

a maximum frequency of f

OCnA = fclk_I/O/2 when OCRnA is set to zero (0x0000). This feature is

similar to the OCnA toggle in CTC mode, except the double buffer feature of the Output Com-

pare unit is enabled in the fast PWM mode.

16.10.4

Phase Correct PWM mode

The phase correct Pulse Width Modulation or phase correct PWM mode (WGMn3:0 = 1, 2, 3,

10, or 11) provides a high resolution phase correct PWM waveform generation option. The

phase correct PWM mode is, like the phase and frequency correct PWM mode, based on a dual-

slope operation. The counter counts repeatedly from BOTTOM (0x0000) to TOP and then from

TOP to BOTTOM. In non-inverting Compare Output mode, the Output Compare (OCnx) is

cleared on the compare match between TCNTn and OCRnx while upcounting, and set on the

compare match while downcounting. In inverting Output Compare mode, the operation is

inverted. The dual-slope operation has lower maximum operation frequency than single slope

OCnxPWM

clk_I/O

TOP

-----------------------------------

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式